Akcesoria do obudów
Diatec
Atrakcyjne obudowy o płaskim profilu
Te bardzo atrakcyjne obudowy o płaskim kształcie są szczególnie odpowiednie dla środowiska domu i pracy. Idealne do komunikacji i urządzeń sieciowych.
- nowoczesna, płaska obudowa do montażu na ścianie lub elektroniki biurkowej
- centralny panel sterowania do montażu klawiatury, ekranu dotykowego lub wyświetlacza
- wnęka do montażu i ochrony interfejsów, złącz, przepustów kablowych itp.
- łatwy, niewidoczny montaż ścienny; zapięcia w bazie
- cztery rozmiary w dwóch kolorach
- DIATEC XS: obudowa dwuczęściowa, składający się z górnej i dolnej części, skręcane, zintegrowany uchwyt baterii na 2 x AA, profilowany uchwyt dolnej części
- DIATEC S, M, L: obudowa czteroczęściowa, składający się z części górnej i dolnej, jak również dwóch okładek ukrywających wkręty montażowe; W razie potrzeby, pokrywy mogą być zablokowane, aby zapobiec nieuprawnionemu dostępowi; Zintegrowany pojemnik baterii do 2 x AA lub 1 x 9 V
- panel slot-in (akcesoria) może być używany w celu oddzielenia obszarów dla elektroniki
- klasa szczelności IP 40
- przystawki na panelach bocznych umożliwiają montaż bez demontażu panelu górnego (S, M, L)
- wewnętrzne słupki pod PCB
Obszary zastosowań
Urządzenia peryferyjnych do komputerów, IoT/IIoT, systemów danych, systemy gromadzenia danych w pracy, kontrola dostępu i zabezpieczeń, urządzania pomiarowe i sterowania, medyczne i laboratoryjne technologie, itp.
A9092107
DIATEC XS
Two-part case. The bottom part can be fixed directly to the wall, the top part is fixed by Torx T10 stainless steel screws from above or below. Recessed operating area to protect the membrane keyboard. Fastening pillars in the bottom and top part. Integrated battery compartment for 2 x AA.
Supply Top and bottom part, assembly kit
A9092107
DIATEC XSprodukt został dodany do twojej listy
off-white RAL 9002
150x37x155mm
A9092108
DIATEC XS
Two-part case. The bottom part can be fixed directly to the wall, the top part is fixed by Torx T10 stainless steel screws from above or below. Recessed operating area to protect the membrane keyboard. Fastening pillars for PCB in the bottom and top parts. Integrated battery compartment for 2 x AA.
Supply Top and bottom part, assembly kit
A9092108
DIATEC XSprodukt został dodany do twojej listy
lava
150x37x155mm
A9093107
DIATEC S
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars for PCBs in bottom and top part. Integrated supports for 2 x AA / 1 x 9 V.
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9093107
DIATEC Sprodukt został dodany do twojej listy
off-white RAL 9002
210x48x200mm
A9093108
DIATEC S
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars for PCBs in bottom and top part. Integrated supports for 2 x AA / 1 x 9 V.
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9093108
DIATEC Sprodukt został dodany do twojej listy
lava
210x48x200mm
A9094107
DIATEC M
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars for PCBs in bottom and top part. Integrated supports for 2 x AA / 1 x 9 V.
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9094107
DIATEC Mprodukt został dodany do twojej listy
off-white RAL 9002
270x48x200mm
A9094108
DIATEC M
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars for PCBs in bottom and top part. Integrated supports for 2 x AA / 1 x 9 V.
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9094108
DIATEC Mprodukt został dodany do twojej listy
lava
270x48x200mm
A9095107
DIATEC L
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars in the bottom and top part. Integrated battery compartment for 2 x AA / 1 x 9 V. If required the hinged lid S can be mounted either on the right or on the left to partially cover the dialog area (on one side).
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9095107
DIATEC Lprodukt został dodany do twojej listy
off-white RAL 9002
330x48x200mm
A9095108
DIATEC L
Four-part case. The bottom part can be fixed directly to the wall, the top part will be assembled by means of screws from the front. 2 side trims close the case. If required, the trims can also be locked, thus preventing unauthorised access. Recessed operating area to protect the membrane keyboard. Fastening pillars in the bottom and top part. Integrated supports for 2 x AA / 1 x 9 V. If required the hinged lid S can be mounted either on the right or on the left to partially cover the dialog area (on one side).
Supply Bottom and top part, trim left and right side incl. 2 locking elements, assembly kit
A9095108
DIATEC Lprodukt został dodany do twojej listy
lava
330x48x200mm
A0306031
Self-tapping screws 3 x 6 mm (PZ1)
Self-tapping crosshead screw (PZ1), specifically suitable for plastics. For fastening components, boards and PCBs onto pillars.
Supply 1 self-tapping screw
A0306031
Self-tapping screws 3 x 6 mm (PZ1)produkt został dodany do twojej listy
A9160003
Plug-in contact, 1 x 9 V (PP3)
Version: Lateral cable exit. Cable length approx. 100 mm. Diameter of contacts = 5.7/5.3 mm.
Application: for a 9 V flat battery (PP3).
Application: for a 9 V flat battery (PP3).
Supply 1 plug-in contact
A9160003
Plug-in contact, 1 x 9 V (PP3)produkt został dodany do twojej listy
A9190002
Set of battery clips, 2xN/2xAA/2xAAA
For contacting the batteries.
Note application ART-CASE: only for base suitable (2 x AA).
Note application ART-CASE: only for base suitable (2 x AA).
Supply 1 double contact, 2 single contacts
A9190002
Set of battery clips, 2xN/2xAA/2xAAAprodukt został dodany do twojej listy
tin-plated
A9190015
Set of battery clips, 2 x AA
For contacting the batteries. Complies with DIN EN 60601. The modified geometry rules out the possibility of a short circuit when inserting the batteries incorrectly!
Supply 1 single contact positive, 1 single contact negative
A9190015
Set of battery clips, 2 x AAprodukt został dodany do twojej listy
nickel-plated
A9194007
Slot-in panel
The slot-in panel can be used as interior partition or separation, for example to protect the electronics when changing batteries. Integrated guide ridges, max. 2 slot-in panels each case.
Supply 1 slot-in panel
A9194007
Slot-in panelprodukt został dodany do twojej listy
off-white RAL 9002
156x30x3mm
A9207150
Anti-slide feet 6.5 x 2 mm
Rubber feet with self-adhesive foil facilitate a secure position.
Supply 2 rubber feet
A9207150
Anti-slide feet 6.5 x 2 mmprodukt został dodany do twojej listy
A9212330
Anti-slide feet 12 x 3.5 mm
Rubber feet with self-adhesive foil facilitate a secure position.
Supply 2 rubber feet
A9212330
Anti-slide feet 12 x 3.5 mmprodukt został dodany do twojej listy
B1360048
Wall suspension elements
Two-part construction. The adapter is screwed down together with the base part of the case. Due to preshaped pockets, each case can be quickly and securely unlatched from the wall suspension element.
Supply 1 wall suspension element, 1 adapter 58 x 128 mm, assembly kit
B1360048
Wall suspension elementsprodukt został dodany do twojej listy
pebble grey RAL 7032
Opcje dostosowywania dla Diatec
Czego potrzebujesz do spersonalizowania, swojego produktu? Dostarczamy obudowy i pokrętła wraz ze wszystkimi niezbędnymi wymaganymi modyfikacjami.
