Accessori per contenitori
C7020061
IN-BOX
Two-piece plastic enclosure with sealing foamed into the top part. Recessed panel to protect membrane keyboards and design foils. Attachment domes for DIN rails, PCBs and mounting plates. Rational stainless steel quick-action lock outside the sealing area.
Supply1 bottom and top part each with sealing, assembly kit incl. cover retention and 4 self-tapping screws for installation configuration
Disegno PDF 2D
3D/2D download
3D/2D download
Create la vostra scheda dati PDF per C7020061
Selezionate le informazioni prodotto per la vostra scheda dati.
Aggiungi al carrello 
Accessory "protection"
C2306917
Pressure equalisation element M6x0.75
Pressure equalisation elements with highly improved air exchange for protecting sensitive electronics. Changing atmospheric conditions and a sudden decrease in temperature can cause underpressure inside protective housings of technical equipment. Water and dirt can penetrate the gaskets damaging electronics in the process. The patented IQ TEX® technology is the ideal solution for urgent pressure balancing in large control cabinets and all protective housings. At the same time the innovative construction of IQ TEX® protects against foreign material and dirt. If required, it is absolutely watertight up to a pressure of 6 bar.
Airflow: 6.5 L/min - 0.25 bar; 16.5 L/min - 1 bar.
Water entry pressure: > 6 bar.
Temperature range: -40°C/+110°C.
Sealing material: BASF Luquafleece + PA6 mesh (insert molding).
Airflow: 6.5 L/min - 0.25 bar; 16.5 L/min - 1 bar.
Water entry pressure: > 6 bar.
Temperature range: -40°C/+110°C.
Sealing material: BASF Luquafleece + PA6 mesh (insert molding).
Supply 1 pressure equalisation element, 1 seal washer, 1 nut
C2306917
Pressure equalisation element M6x0.75Prodotto aggiunto alla lista
light grey RAL 7035
C2310917
Pressure equalisation element M10x1
Pressure equalisation elements with highly improved air exchange for protecting sensitive electronics. Changing atmospheric conditions and a sudden decrease in temperature can cause underpressure inside protective housings of technical equipment. Water and dirt can penetrate the gaskets damaging electronics in the process. The patented IQ TEX® technology is the ideal solution for urgent pressure balancing in large control cabinets and all protective housings. At the same time the innovative construction of IQ TEX® protects against foreign material and dirt. If required, it is absolutely watertight up to a pressure of 6 bar.
Airflow: 19.5 L/min - 0.25 bar; 43.5 L/min - 1 bar.
Water entry pressure: > 6 bar.
Temperature range: -40°C/+110°C.
Sealing material: BASF Luquafleece + PA6 mesh (insert molding).
Airflow: 19.5 L/min - 0.25 bar; 43.5 L/min - 1 bar.
Water entry pressure: > 6 bar.
Temperature range: -40°C/+110°C.
Sealing material: BASF Luquafleece + PA6 mesh (insert molding).
Supply 1 pressure equalisation element, 1 seal washer, 1 nut
C2310917
Pressure equalisation element M10x1Prodotto aggiunto alla lista
light grey RAL 7035
C2320137
Cable grommet
Simple cable grommet, easy to install, with easy-to-pierce membrane. Tight fit as soon as the cable is pulled backwards a little. Free of halogens. Suitable for wall thicknesses from 1 - 4 mm and for cable diameters from 8 - 13 mm. Operating temperatures from -40°C to +100°C. Borehole ø 20.5 mm.
Supply 1 cable grommet
C2320137
Cable grommetProdotto aggiunto alla lista
light grey RAL 7035
C7100138
Security kit
To secure the enclosure against unauthorised access.
Supply 1 security kit
C7100138
Security kitProdotto aggiunto alla lista
Accessory "wall/holder"
A9325018
Pole/mast mounting bracket
For the secure and stable mounting of IP rated electronic enclosures to poles, masts, and pipes using cable ties or stainless steel screw bands, suitable for pole diameters from 30 mm. The bracket is attached to the rear of the enclosure (four drilled holes required) and is manufactured from UV resistant material.
Note:
Every application (environment, sealing requirements, enclosure size/version, mast diameter, etc.) is different. For this reason, no mounting screws, cable ties or stainless steel screw bands are supplied; only the mast/pipe bracket is included. However, on request, we can provide a wide range of solutions tailored precisely to the intended application.
Supply 1 pole/mast mounting bracket
A9325018
Pole/mast mounting bracketProdotto aggiunto alla lista
anthracite grey RAL 7016
100x100x20mm
C7100092
Wall-mounting brackets
Wall-mounting brackets made of plastic for external wall mounting. Installation above, below or laterally, as required.
Supply 4 wall-mounting brackets incl. fasteners
C7100092
Wall-mounting bracketsProdotto aggiunto alla lista
C7100142
Inside hinge
For converting the top part of the enclosure into a folding door.
Supply 2 hinges, fastening screws with drill template
C7100142
Inside hingeProdotto aggiunto alla lista
Accessory "screws"
C7100167
Screw 3.9 x 9 mm
For fitting standard DIN rails, mounting plates, PCBs, components etc.
Supply 1 self-tapping screw
C7100167
Screw 3.9 x 9 mmProdotto aggiunto alla lista
Accessory
C7115056
Mounting plate
Mounting plate made of insulating material with 4 holes drilled in it, for attachment in the bottom part of the enclosure.
Supply 1 mounting plate
C7115056
Mounting plateProdotto aggiunto alla lista
C7115077
Standard DIN rail, Type TH 35
Standard DIN-rail in accordance with DIN EN 60715, 35 x 7.5 mm. For mounting terminal blocks and components in the enclosure.
Supply 1 standard DIN rail TH 35
C7115077
Standard DIN rail, Type TH 35Prodotto aggiunto alla lista
184x35x7,5mm
C7115087
Standard DIN rail, Type TH 15
Standard DIN-rail in accordance with DIN EN 60715, 15 x 5.5 mm. For mounting terminal blocks and components in the enclosure.
Supply 1 standard DIN rail TH 15
C7115087
Standard DIN rail, Type TH 15Prodotto aggiunto alla lista
184x15x5,5mm
Customising options for C7020061
What else do you need to create your own personal product? We can supply our enclosures and tuning knobs fully modified to suit your electronic components and design requirements. Please advise for anything else we can do for you.
- Dati tecnici
-
Disegni / Informazioni
- Purchasing Data
Materiale
Protection class
,
,
Colore
light grey RAL 7035
Standards
The degree(s) of protection listed refer to the empty standard enclosures (without any modifications) and are in compliance with the EN 60529 standard.
Lunghezza
202 mm
Larghezza
122 mm
Altezza
90 mm
PCB length, base
171 mm
PCB width, base
113 mm
Keypad length
174,75 mm
Keypad width
94,75 mm
Please take the dimensions from current parts. These are subject to material- and manufacturing-specific tolerances.
Drawings (Discrepancies depend on material-specific manufacturing tolerances, e.g. DIN ISO 20457)
- PDF-File (without registration) 338 KB
- AutoCAD DWG-File 742 KB
- AutoCAD DXF-File 2.809 KB
Weight/1 part
394 g
Customs tariff number
(OKW product)
(OKW product)
39269097
Country of manufacture
Other country
Servizio di customizzazione : Possiamo modificare i nostri contenitori per soddisfare le vostre specifiche esigenze. Saranno consegnati completamente finiti e pronti all’uso. Dovrete solamente installare la vostra elettronica al loro interno. Visualizza le opzioni di customizzazione C7020061 e non dimenticare di chiedere la quotazione!